- Rayspeed - RC10B4 Tips

Maintenance
Here method and procedure of simple maintenance after the travelling are introduced, with 2WD the damper mission of the liver 　If  it does, because the how thing which “the car does not run recently” decreases, we would like to introduce around this preponderantly. 　First you remove the mission and the damper and in every block maintenance that try it is possible.
The off load car after the travelling is dirty with the mud and the dust So, beforehand the soiling is removed with the air and the brush.	If case of [hurumente] is excluded, the rose doing to here, the bucket It probably is sufficient as always [mente].
The ○ first, the mission disassembling, begins from the place where you drop the grease and the mud soiling which come in contact with the gear. To remove the soiling, in the toothbrush 　It blows the cleaner and [goshigoshi] does, it does not do that the cleaner is blown directly.
When the mission is disassembled, the grease and the dust etc come in contact, The soiling is accumulated in the opening of each gear.	Although the soiling is removed, the tooth brassiere which blew the cleaner [shi] is used.
Removing the soiling which accumulates politely in the opening of the gear politely It goes. When this time the cleaner is blown directly, The resin and the bearing will be avoided because it can hurt.
Being at the point where the ○ soiling falls, this time it is disassembly cleaning of the diff., when (the diff. still is the sail sail, necessity is not), this time the genuine men 　Because by the fact that [tenansukitsuto] is used the thrust bearing and the spring become the new item a state where the diff. is good easy to maintain 　It becomes.
Being the plier, it be sure crushes the brand-new spring, the [ma] It does. Now looseness of the early diff. can be cancelled.	The soiling and the oil and fat which have come in contact with the cleaner the washing style stripes It does.
When the grease and the oil and fat remain, the diff. to slide, [su] Because there are times when the differential motion it does not do in the moose, note is necessary.	The bearing and the diff. ball which finish washing are attached, the [ma] It does, this time you will wash also the hand and the pincette.
The ○ diff. gear using the cleaner and blow, removes the grease which remains completely, excluding the case where the diff. ball you exchange, 　You wash cleanly with the cleaner. And it is the assembly, but painting the black grease fully in the thrust bearing 　The installation, the ball is installed in also the diff. gear and the diff. grease is painted fully.
The black grease fully in the bis of the joint heaping The [ru] way it paints.	The feeling which keeps placing the ball of thrust in the grease which you piled up So it keeps uniting.
When the plate of thrust is placed 1 already, this time the opening In order to bury between, it paints the black grease and is packed.	When it installs joint bis in the diff. joint, In order to pull both it tries turning. This time [gori] If [gori] it does not do and/or does not do roughly it is OK.
The ○ it paints the diff. grease thin in the joint of the diff. ring and the diff. joint which remove fat in order to push both it makes stick, 　When it neglects this, it is what, because it becomes the diff. which it slides note is necessary. Well it is the assembly, but the diff., rigging [ne] 　It keeps screwing [ji]. All it tightens screwing and it is the place where 1/4 revolutions you reset from state and is OK. 　The part is installed in the mission case in this state, the small quantity painting the diff. grease in each gear, to assemble, for connecting the case 　Bis if it does not loosen it keeps tightening, is completion. It is the tightening condition here, but the wrench is turned concretely with the fingertip, 　The [tsu] [te], [kiyutsu] being the place where it tightens, it is good being the extent which stops probably will be. When turning the top shaft with the fingertip as an allowance, 　The grease which was painted in the gear it is heavy you feel it is good being, probably will be, it is useless to be astringent of course.
The diff. grease the small quantity is painted in the diff. joint. [jiyo] The fact that it does not slide on [into] and the ring is purpose, but the [a] When the ball it paints mainly, because it becomes the counter-result, note is necessary.	In the joint which painted the diff. grease uniting the diff. ring It is packed, while this time turning the diff. ring, the grease While familiarity it makes stick with the feeling which is pushed.
The diff. grease is painted even in the diff. ball and the diff. ring. The quantity is not too multi, it is the place where be too little you said.	To install the diff. joint left and right in the diff. gear, all From tightening joint bis is screwed with 1/4 resetting. The grease sees and comes out and comes coming out but the quantity of this rank is optimum.
When it installs each part in the body, the diff. grease [gi] The small quantity it paints in [ya], this grease traction raw It is to discover.	If it adjusts the case and installs the motor plate completion Is. As for tightening condition of bis of this time wrench with fingertip tightening The [me] [ru] is good, probably will be.
The ○ it is [mente] of [suritsupa] next, the plate and the shoe of [suritsupa] which the rose is done are the expectation which certainly becomes [tekateka]. 　Now original efficiency is not shown, the acceleration impression becomes dull and/or jump stops being able to fly, with there is no good thing. First 　The shoe, you put in place the shoe which in the level place has become [tekateka], shave the surface with the cutter knife and the like thin veneer peel. On surface gloss 　If is gone, it is OK. Because the plate, this the soiling has come in contact with the surface next, it polishes with those of detail of the nylon file, the [ma] 　It does, if the surface becomes clean, it is OK.
[suritsupashiyu] before [mente], even with photograph [tekatsu] [te] [ru] Is recognized, when it becomes like this, as for the car before not coming out The [ri] it increases.	Using the cutter knife on the level stand, the chart of the shoe The [gi] is dropped it shaves very the surface with the feeling which.
Like the photograph if [tsuya] is gone, OK, with this the work at the time of the new item Motion revives.	As for this refuse of [suritsupapureto] and shoe flattery The [ri] arriving, it is dirty. Now as for honest operation period 待.
With the nylon file where the eye is small then the plate surface It polishes. As for having used with the photograph G style make It is the tire thunder.	When it polishes the plate, so it becomes clean, this So as for [suritsupa] which recovers original efficiency preeminent [tora] It probably is to show [kushiyon].
The part of [suritsupa] which if the ○ cleanup is done is installed in the mission, it is completion, it is the screwing quantity of [suritsupa] here, but 　It screws the nut to the screw and flush of the top shaft, furthermore 3 revolutions and 3/4 screws from there. This in standard [guri] 　When in the road surface where [tsupu] is good 4 revolutions and grip are bad, if 3 revolutions and 1/2 you use properly, it is good, probably will be.
Mission and [suritsupa] which you refresh are united, attaching The [ke] [re] completion, this time without forgetting either washing of the hand.	At description above recording standard screwing rpm of [suritsupa] It increased, but as for “flush” of standard the photograph for the reference.
Before uniting the mission to the shear sea, with the dustcloth the butterbur butterbur. This time check of crack such as underside propriety!	Even in pin of dog bone grease rise and [haiburitsu] All range barrier of [to] is used.
The ○ it is maintenance of the damper next, the damper the rose is done first and each part washes. When washing ends, the O ring is exchanged, 　It increases, after making the green slime to the O ring adapt which is exchanged fully using the private tool, it installs politely. 　When the piston is installed, damper oil is inserted, when oil enters, this time it is the air, the shaft is moved up and down 　Because with the air bubble passes from oil, leaving this for a while, until the air bubble is gone completely, it waits, the air bubble is gone 　The air is completion. More and more it is the assembly.
Reverse side skill when the O ring is not exchanged. WD-40 [shiyahu] It blows to [to], the shaft it just is moved up and down.	With the photograph you understand and are harsh it is, but [doro] in it is certainly dirty The [re] has started dissolving. It was or more reverse side skill.
Returning to this subject, it makes first the front part disjointed.	Oil and the soiling which remain from the cleaner are washed away.
Even then as for the soiling which remains you blow with blow and throw.	The internal part this way because it is dirty with [doro] and the like, Being the cleaner you wash away well.
If you wash, cleanly, breaking so, it reaches, the unskillful [tsu] [te] It is reuse possible excluding the case where it is.	Before uniting the brand-new O ring, just a little one job.
By the fact that this green slime is painted the O ring itself 寿 Life extends, to call mud [yogore] is an effect which makes difficult, the [ma] Because it does, it becomes easy to maintain the efficiency of the damper.	Way it spreads well, in vinyl the green slime Inserting it rubs well and is packed and makes adapt.
The tool is used and [purapatsu] and the O ring are installed Most even in part with respect to this state green slime It paints.	The ended ball is attached to the damper shaft, This time the end is tightened to the screw cutting top of the shaft, 込 Seeing 2 revolution the place where you reset is designated as length of standard.
Oil is inserted in the damper, with the off load especially Because difference of efficiency of oil is easy to appear, the [asoshi] genuine recommendation It does. It can cover the count around this.	It keeps pouring oil, but this time the excessive air In order not to mix, the bottle being able to tilt if possible, you work With it is good, probably will be.
When oil is inserted to the edge, moving the shaft up and down The air which it mixes is bled.	Because the air floats in large quantities in such a wind, this Leaving, it waits for the fact that the air goes out.
The air coming out, it is accustomed to such a wind and time is good the damper It moves to the assembly.	Here the group which uses the damper cap of [yokomo] make Because the seeing raising is introduced, the [a] it does, not driving. [bi] of cap [su] loosens beforehand to screw 2 pile leaving rank.
Oil is added to the damper which the ○ air comes out but oil is the [ri] does the quantity densely with boundary tension to inserts. In this 　After inserting oil to the screw drill part in the cap of the damper which it adjusts if it installs in the damper and tightens it is OK. This 　It is the cap, but by the fact that the cap of [yokomo] make is used job to become easy, because the quantitative assembly is possible, you use the male 　The rice it increases. 　Uniting shortening the shaft of the damper which rises, it pulls out unnecessary oil, the bis which this time by all means has been attached to the cap and is on 　Directing in order to work, please does, side and under when it is faced, the air not passing through, only oil to finish coming out, original efficiency 　Because you cannot show and become note is necessary. To push in the shaft to end slowly, the bis of the cap tightening 　If the [me] it is packed, it is completion.
Until it is the [ri] it makes densely the damper which the air is finished [oi] You pour [ru] and add. Even on cap side lower [ma] of screw cutting So oil is poured.	In order not to drop oil, screwing in both extremely quickly with the industry It assembles. When it assembles, the screw of the cap on To push in the shaft when it is directed, the excessive air Oil is pulled out.
When the shaft is pushed in entirely, that way [ne] of the cap [ji] is screwed and it is completion.	As for the damper which can be united with the chitin one time stretching, when you separate, copying Like the true left it returns to length. The photograph right in front Noboru state Because it does, comparing, please see in reference.
It is the installation to the chassis, but that the installation nut above is not tightened too much, you will note, if it moves smoothly, it is OK.
The damper which you complete is united to the shear sea, but taking The attaching nut not to be too gentle, the [kitsu] not passing. Abnormal play minimum If after doing, it moves with clattering to left and right, it is OK.	Damper mission and installation last finish. WD-40 is blown to the moving element. Does not depend on the mechanic The way it will cover with the towel and the like.
If it makes WD-40 ADAPT with the brush, completion, like this doing So at the time of next travelling in addition to becomes dirty and being harsh, even in the suspension pin and the like The oil content to be supplied, operation smoothly. Most shining It becomes and it is something whose feeling is good.	Shining, it becomes [surusuru], completely the refreshment B4 which it does, always with empty this maintenance always It becomes possible to pull out the potential of the car, the [ma] Because it does, propriety try.

Height Adjustment
It introduces the how very important height to adjust as a setup point of the off load car, settee Because it measures the height which is stated in [ngushito] with this method if it becomes reference, with you think.
The ○ first holding down around center of the shear sea when the electric battery & the motor are attached to shorten the damper, releasing the hand 　The [te] it measures at the place where it returns. As for measurement place anterior front suspension arm rear end, rear side rear suspension arm 　It makes near the front end, it is good measuring with the yardstick and the like, is, but because numerical value is easy to change with the angle which is seen by all means [re] 　We recommend the use of height gauge for [isupido] make off load. As for the point of caution before by all means measuring the height, the chassis 　[hekoheko] pushing the central part, putting in the state of 1G, good [hekoheko] doing the front and just the rear, height 　The one which you measure is discovered, but when this it is, because accurate height measurement is not possible, by all means around center [heko] 　[heko] please do.
With height gauge and yardstick for ray speed make off load It is substitution possible, but if it is possible, use of such tool We recommend business.	Before the measuring by all means with like the photograph, several degrees pushing the car It is important to put out the state of 1G securely.
Measurement place the rear is the coconut, the setting seat You assure also measurement value with the coconut.	Measurement place the front is the coconut, each time as much as possible In order to be able to measure under the same conditions, you will try.

Tuning Tips
Even in the setup which the ○ recently has been tried Tips which has been liked is introduced, as for these mainly the May present time 　The topic that has been center with try with [yatabearina], from it makes traction.
On left and right of rear end of shear sea weight at a time 7g meter 14g is placed, even just this traction Catching considerably becomes good.	The varieties you tried also the wing, but it pushes out, impression [supi] Both [do] balance being good is LOSI make aurora win It was [gu].
By the fact that installation position of the rear upper arm is lowered [ri] You aim for the traction improvement of [ya], both the inside and outside the shim At a time 1 it is pulled out.	When this rises and descending the difference in level and the dent with respect to course The front being caught, inserting power is [wante] [npo] being late dislike, the knuckle is being increased on It is the figure.

Building Tips
○ this time the point of the RC-10B4 factory kit assembly is introduced. Even with assembly of according to instruction manual It is this kit which shows sufficient efficiency, but encounter and secret in order to prevent trouble beforehand and the characteristic which it can have Chasing order, it keeps explaining Tips which furthermore can show talent.
Before beginning the ○ assembly, the part where the one which is arranged to other than the kit is good is introduced. Be sure to do these, 　It is not to be the meaning that it is needed, but if compared to it becomes reference when encounter applications are designated as prerequisite, with you think, introduction 　You can point to mediating/helping. 　AS-9560 composite main chassis 　AS-9578 front " A " arm 　AS-9582 rear " A " arm 　AS-9566 top plate 　AS-9568 front shock tower 　AS-9572 rear shock tower 　AS-9564 R chassis /F hinge pin brace 　AS - 959,330 degree caster block 　AS - 965,278 T spur gear 　FTP-1780 shock bush 　SP-7369 stubby pin for axle 　FTP-1595 chassis balance weight 　RS-28 the aluminum rear hub carrier 0.5° for RC-10B4 　RS-29 the front bulkhead for RC-10B4
Holding the factory kit, it is Noboru of rapture. This Group it keeps increasing empty this.	Among the kits which originally are adjusted to the super high grip road surface Permitting/inserting. Naturally in the Japanese domestic track/truck because the chassis is too hard the resin part of principal is replaced with the normal part.
Installing such functional part at the time of the new model car assembly When you put, the rear becomes easy. Now because it is the part of fixed turn, propriety! (Advertisement)	As for bearing of kit standard in all rubber seals It has become, but in the place where it receives the influence of the dust and the like is harsh the limit [tsu] As for the [te] by the fact that you exchange to the usual bearing, from [sumu] [zu] operation obtain.
The ○ then the assembly is begun, here there is no abnormal play of the part such as the suspension arm and the mission, smoothly 　Operating it keeps advancing job in mind. In addition, while travelling in order to evade the trouble which can happen 　Because it keeps introducing also Tips simultaneously, as for the race/lace user please try making especially reference.
First from front section. As for resin part politely Bali is taken.	In regard to the installation of servo saber volt/bolt one. In order that this is attached, in the resin part the servo saber It screws.
Volt/bolt is removed once here,…	To let flow the instantaneous adhesive agent to the thread which can be made the resin part, for the second time This is installed. Like this it is in the midst of travelling with doing Steering wheel around abnormal play occurrence do the fact that prevent thing come out It comes.
When the steering wheel wiper unites and rises repelling with the finger If you verify operation and move to the sail sail it is OK. If it seems the astringent way, the rose doing once, it resets.	To aim toward smoother operation, in the suspension pin fluorine adding Manufacture is done. The cleaner it is good being as preliminary arrangements removal of fat It does.
To process the surface making use of the chemical of fluorine combination, dry When it is, group it keeps lifting.	As for having regularly used [wakozukemikaru] make [hutsusooiru] Because 105, it is dry process, the dust and the rubbish are not allowed to come near. You use for pulley what of the pulleys.
The occasion where the ray speed make aluminum bulk is used, [bure] In the bis which installs [su] the screw lock medicine the application stripe It does. As for bis when it tightens too much, the movement of the suspension arm astringent Because it becomes, note is necessary.	Those of 30 degrees are used to the hub carrier, you take, attaching The case of the [ke] way in any case it is not smooth and abnormal play, prudence Attention is paid.
In tie rod the rod end and lance of LOSI make The ford turn buckle is used. As for this rod end of kit standard item compared to LOSI make Because one is hard, comes off and is harsh, breaks and is harsh liking, using It is. In regard to the turn buckle the kit standard item From the reason that in lance Ford make also the [ri] [moguri] is harsh, You have exchanged.	The front section is completion now. Tie rod Chile it will be also the eye which was seen by the fact that you exchange angry, in the actual running To be strong in hit and crash, mounting the aluminum bulk So being smooth, has the rigid impression in the front section which It came.
It keeps assembling the mission next, the men of Tips Because it has explained in detail with the [te] compilation, as for details this So.	So, the part which has not been touched with the [mente] compilation is introduced. Copying [rabashi] of the kit standard where the true right goes in the mission [rudobearingu], this in sealed bearing the left You exchange making smoother mission by the fact that It is possible. (Smaller one just 4 are)
Bearing with cleaner after the removing fat, [yokomo] make F-0 Applying, it finishes in the bearing whose resistance is less the [ma] It does.	As for F-0 rather than saying that it blows, way at a time the small quantity it pours in, Note it keeps doing with feeling.
The plate of [suritsupa] before attaching, beforehand [nairo] Rubbing on [nyasuri], it trains the surface. It is dense It is thin, with [ru] thing, first stage 喰 it is and can prevent the attachment.	The mission is completion now. Turning with the finger, smooth At the same time it is a little heavy, if you can obtain the feel which is, being good, it does, the [yo] When the [u], [shibu] you apply and/or are caught it is resetting.
It keeps assembling the rear section, the rear suspension Because basis of the arm is easy to come out abnormal play, inserting the shim beforehand When abnormal play is taken, it is good, probably will be.	You screw in [borisutatsudo] to the aluminum hub carrier The screw lock medicine is applied before. When here loosens, baud Because [rusutatsudo] is likely to break, note is necessary.
Even the case of C.V.D assembly in [imoneji] screw lock medicine coating When the cloth it does, it can prevent looseness.	Because the rear axle hinge pin of standard is easy to break, SP- You exchange to the pins for 7369 stubby axle.
As for the pin which you exchange because a little it is thin, in coming out prevention the shoe goo After and so on the small quantity applying, it attaches.	The ball stud is installed in the rear brace. But when is just this, if it is easy to loosen, loosens it breaks Because….
So, the ball stud is removed once, the instantaneous adhesive agent [bure] It pours in to [su], assembles for the second time. Like this by the fact that it does It can prevent looseness.	The mission is installed in the brace, but installation When bis is exchanged to pan bis [ru] occasion, [mente] after Becomes easy.
When bis is exchanged with such feeling, with wrench 1 The around of the mission becomes disassembly possible. Laziness we would like to do As for one propriety.	With [potsuchi] which stops the body above the rear suspension mount It does, but without using you stop the body itself with Velcro The way it modifies. Like this when it does, the body and in the [bu] [ke] [zu] It lasts long.
Assembling the tie rod next, you install, but before the installing In ball end of hub carrier side hole of 2 millimeter rank You open.	When it does, the wrench directly in six square holes of the ball stud [aku] It becomes [sesu] possible. Like this it sets up by the fact that it does Occasion the necessity to remove the ball end to be gone, forcing Because it becomes also prevention of coming out [guse], we recommend.
The rear section completed with such feeling.	It is the shear sea next, but when the mechanic is placed beforehand, after Job becomes easy.
Next the shear sea anterior coconut.	By coconut of rear side weight of 7 grams left and right each 1 at a time When 4 total it places, balance when travelling becomes good.
When each section finishes assembling, these each one Group it keeps lifting.	It is the tie rod of steering wheel servo, but the resin part Long [imoneji] where it connects from inch size of standard the 3× When you exchange to millimeter screw ones of 10 millimeters, it comes out, in prevention the possession It is effectiveness.
Paying attention into sense, locking the tie rod with the instantaneous adhesive agent It does.	The tie rod which it assembled is installed.
The case where the tie rod is installed, neutrality of the steering wheel You verify that it has come out with the chitin.	From cap bis modifying the bis of the coconut in pan bis When you put, the case of service, ease is possible.
It is this bis, on with pan bis under kit standard It is cap bis.	Generally it became shape, it is rear taking a rest, but after this The assembly of the damper is one work.
It is the assembly of the damper, but first the [pura] section which goes inside Quarrying out the item, it removes Bali with the cutter. Even number It is important to finish in the 寧.	Major diameter of the washer which enters into the place of the O ring the verification stripe It does. It does not do this with not be able to obtain the smooth movement, characteristic Because it is not possible to pull out talent, the execution stripe be sure to do, the [yo] [u].
As for method like photograph washer in damper case [su] You verify whether or not it enters into [muzu]. It resists even a little When it seems that is felt, it is deficiency.	Even, a little [kitsu] those which are felt shave around with the file, learning/repairing The righteousness is done. Compromise travelling efficiency is large even with the coconut left and right Because it does, spending time, working thoroughly, under It is.
It keeps attaching the rod end of the damper prudently, the [ma] It does. Way the scratch is not attached to the shaft of the damper, note Mind is necessary.	When it attaches, removing once, the screw cutting section of the rod end After letting flow the instantaneous adhesive agent to amount, it assembles for the second time. It is dense Thin it becomes the coming out prevention which is in the midst of travelling with [ru] thing.
When the cap of the damper is exchanged to [kore], job With respect to ease the assembly of the quantitative damper becomes possible, the [ma] Because it does, we recommend use regardless.	When oil is inserted in the damper, secure the air removal After being, it assembles. The main point where here is detailed is dense With [chi] and others.
If the damper which you complete is installed in the chassis, it to be possible, on The [ri], then it keeps leaving the small place.	It is digression, but the place where VFS-1 whose recent activity ratio is high is loaded It is example of combination. Schottky diode and [konden] When the routing of the sir is designated as like the photograph, drying of the body The 渉 prevents, at the same time becomes the smart eye which was seen.
It is the sponge which holds down the battery, but 1 angry It cuts to half thickness with the tar.	With such feeling sponge of the same thickness 2 completion Is.
As for 2 sponges on front and back of battery slot 1 At a time it arranges.	Installing the tire, contingent completion, well enough time being required It increased.
Arranging camber and toe in lastly, body and [u] Installing [ingu], it is completion.	Because it fights, supporting all Japan by all means with it is dense !

Tires Tips
○ this time you do not talk with other than, it keeps introducing the procedure and reverse side skill of method of assembling the off load tire. 　With saying, usually when it is the method which sends the buggy because only-too-natural just thing, including also the meaning of verification 　Association.
This time it tries making the rear tire of RC-10B4 as an example, It increases. With tire of which kind of car as for main point simultaneous Because, please try referring.	First Bali of the part of [mimi] of the tire is removed. Especially when the import tire (professional line and [rotsushi]) is, processing Because is not done, it is necessary.
Job sort of the photograph reaching, is simple, it comes out with the scissors, the [tsu] The part which it has stretched just is cut off.	The completion is such feeling, when it neglects this job, the tie [ya] does the partial core, because gluing is likely to peel off, by all means and the [tsu] The [te] you will put.
When Bali is taken, this time the mold release agent and the like which comes in contact with the tire Being the cleaner it wipes off well. This job is polite Unless please go, so it does persistently, the tie in the time angle [ya] bursts. Wiping off ended And others preparation of the tire is OK.	It is preparation of the inner sponge next. Before the job photograph The way when it rubs well, early hardness of the sponge itself Being able to come off, “although it is the brand-new tire, the 喰 trap being and” with saying Because it is possible to prevent, propriety.
When it rubs well, it keeps cutting inside inner, the [ma] It does. When here is left, 噛 it is with to make the rib of the wheel, Will not, it increases and, in the sense that it adjusts to the form inside the tire When it cuts by all means, it is good, probably will be.	When it can perceive the quantity of cutting in comparison with unprocessed ones the left You think, having cut well enough at a stroke is the [wa]? The [ri] it increases.
Completion is such feeling. In the past outside inner It cut also side, but as a recent tendency judo Or because the case which uses the tire is many being able to meet, outside It does that way.	It is preparation of the wheel next, as for the instrument which is prepared the knife It is the edge reamer.
The air hole is bored through the wheel, at a stroke with the reamer With 2 places you open on the diagonal.	As for completion as for size of such feeling and the hole it is eye estimate Generally is the 5~6 millimeter. It is too large, when [hoi] Because rigidity of [ru] falls about, in 々.
This time inserting inner in the tire, with the finger [guriguri] Doing, it makes the tire and inner adapt.	Doing persistently, still it increases, in any case inner partial and others In order not to be, [guriguri] it does.
Furthermore after installing the tire in the wheel, by the hand [guri] [guri] doing, it makes adapt. The tire trying touching, hardness If becomes uniform, it is OK.	This time the part of “[mimi]” of the tire is raised with the finger The sea urchin doing, it keeps making the projection of the tire side uniform, It increases. When [mimi] is entered in the wheel, the tire When turning, because the blurring [te] you put away, note is necessary.
Well it is gluing, but the instrument which is used before that. From the left wheel [go] The instantaneous adhesive agent of [mu] and medium viscosity, it is the primer.	First putting the rubber band on the tire, the tire and the wheel It makes the gluing surface stick.
Just a little it turns the side of the tire next with the finger [tsu] [te] instantaneous connection It keeps letting flow the arrival medicine little by little.	This time try the instantaneous adhesive agent not to let flow excessively in large quantities [ru] is secret. When the quantity is too multi, when becoming firm, it glues The crack of the surface to occur, forcing, because it is connected to peeling, note Mind is necessary.
Tracing the gluing surface ahead the nozzle of instant arrival, it becomes uniform The sea urchin it makes adapt. Because also the eye which you saw is finished cleanly Please execute by all means.	When it finishes to let flow the instantaneous adhesive agent, extremely the little primer Blowing, it makes dry. In just primer setting When the [te] you put away, the gluing surface to become very hard, the crack and peeling Because it becomes cause, note is necessary. When it becomes firm The tire is completion.
You completed the ○ tire, but in ahead it keeps introducing from here concerning the balance taking of the tire. Usual 　With practice and race/lace it is to be not to do excessively, but with the big race/lace such as all Japan and world championship by all means 　It has made to do. The effect which is obtained by the fact that balance is taken becomes large, attitude of jump good, 　The grip impression to rise, because it becomes strong even in the gap, as for one time you think that there is a value which is tried.
As for the weight which is indispensable to the balance taking golf and the one for fishing When the board weight is diverted, it is good, probably will be. Foam/home plug It can procure at the tar and the sporting goods store.	First in order to search the part where the tire is heavy in balun sir 載 It does narrowly.
The heavy part coming under the truth, when it stops, the heavy part counter The marking it does on anti- side. In position of marking [omo] Pasting [ri], you apply on balun sir for the second time.	Until the tire stops stopping at position of specification, adjustment continuation The [ke] it increases. When it stops stopping, as for balance you call OK It means especially.
It sticks the weight in such a state.	Now the tire which it can correspond to also big race/lace completes, It increased.